i cant upload car

Más
24 Jun 2016 14:22 #2015 por Fabikan75
i cant upload car Publicado por Fabikan75
Más
25 Jun 2016 00:14 - 25 Jun 2016 00:38 #2016 por tt
Respuesta de tt sobre el tema i cant upload car
Sorry! With server move the permissions are wrong, will check it now!

EDIT: Now it seems OK configured, can you try it now? Deleted the old upload of the 508 ;)
Última Edición: 25 Jun 2016 00:38 por tt.
Más
25 Jun 2016 01:22 #2017 por salatiel
Respuesta de salatiel sobre el tema caminhao
Más
25 Jun 2016 09:36 #2018 por Fabikan75
Respuesta de Fabikan75 sobre el tema caminhao
thanks:)
Más
27 Jun 2016 17:04 #2020 por salatiel
Respuesta de salatiel sobre el tema i cant upload car
  • can somebody make this car?
  • Visitante
  • Visitante
27 Jun 2016 18:03 #2021 por can somebody make this car?
Respuesta de can somebody make this car? sobre el tema i cant upload car
  • Anónimo
  • Visitante
  • Visitante
27 Jun 2016 18:27 #2022 por Anónimo
Más
29 Jun 2016 01:35 - 29 Jun 2016 01:36 #2023 por Skybh
Respuesta de Skybh sobre el tema i cant upload car

Fabikan75 escribió:

Hi,

please do some checks before relasing cars.
I've found a lot of mistake, the biggest one was that the steer were not correctly detached from the interior (some triangles went in gear stick when you detached i think).

The best way for me to seperate a steer, in zm1
  1. create/object/by material/split
  2. Attach all materials containing the steer
  3. Select/seperated
  4. Select your faces properly, and done without mistake (took me 2min to detach from .dff file)

Other mistake, the torque curve.
It is just incredible to keep using normalised curves, on top of that, they were totaly wrong, ok the max torque is at 450Nm, but after that rpm, the power drops until 3200(151hp) and goes up until 4000 (which gives ~190hp).. While the real max power is at 3500rpm..
yet I have explained everything here : www.tracciontrasera.es/forum/racer/121-t...g-about-engines#1022

About aero, an aera of 1m² is just impossible.. in a such car it should be ~2,20m², after few search i've found an SCx of ~0.58 for a Cx of 0.26, which gives ~2.23m².

About gearbox, the ratios where wrong, and shifting point too far (maybe for keeping as manual?)
For ratios, i've found them here : www.cars-data.com/fr/peugeot-508-gt-2.2-hdi-specs/36395

Same for wheel radius, uncorrect..

Also about view, please please please stop to use to uglys digits that i've done few years ago, they're just ugly and boring.

I hope it helps for other relase, because all this new content is just dropping down mods quality for racer :(

Fixing all those thing tooks me less than 3hours, realy (and with reimporting the .dff and re export the file, doing cg shaders etc..).

If I can, you can ;)
Última Edición: 29 Jun 2016 01:36 por Skybh.
Más
29 Jun 2016 08:54 #2024 por Fabikan75
Respuesta de Fabikan75 sobre el tema i cant upload car
Hello, thank you for your suggestions.
After all, when I look at the quality of the mods both old and those produced today. They are much more tragic.
Regarding the curve:
I adjust it and gearbox to accelerate. For me, the real performance have a higher priority than the curve :). With real curve I would have trouble getting 8 sec. + - 0.3
  • cars from gta sa
  • Visitante
  • Visitante
30 Jun 2016 15:36 #2025 por cars from gta sa
Tiempo de carga de la página: 0.638 segundos
Gracias a Foro Kunena